A Trip to Mount Wilson

Sunday July 6 I was able to take a trip up to Mount Wilson Observatory with my mon and my little brother.  In a sentence,  It is a spectacular place to visit.  There is a rich amount of history with a multitude of places to see and things to do!  And a LOT of walking!

It’s a really nice, but lengthy drive up in the mountains to get there, and the road is full of sharp turns.  The whole way up I was trying to picture someone driving that big 60″ and that big big 100″ mirror up the very same road.

Anyway we got to go on a tour of the whole place, or you can just walk around.  I highly recommend the tour, but only on weekends, where they include visiting the observing floor of the 100″ telescope.  There are so many observatories there, I never did a count, but over 5 separate domes, not including another observatory under construction while we were there.

Me and my brother Kevin ready for an exciting (and exhausting) day

Me and my brother Kevin ready for an exciting (and exhausting) day

The first place we visited on the tour was the 150 foot solar telescope.  This was pretty awesome, and it’s pretty darn hard to miss as well, as you could imagine, it’s a big tower.  We were lucky enough to be accompanied one of the people that sketches the sun daily and he showed our tour group inside.  Walking through the door was like walking right back into the good ol’ days of astronomy (not that I ever experienced them myself :D).  Old equipment in use since it was first put into use since 1912.  What was really exciting was the amount of sunspot activity, it was really active that day.  There was a sketch of the biggest sunspot they ever recorded put down next to the live sunspots we were seeing, and they were that much smaller!  Anyway, there was another small room with some really old computers, I have no idea what they were but they had the old reels like you see in the Apollo 13 movie!  There is a live camera on the top of the tower that can be see here.

Shot of the 150-Foot Solar Tower

Shot of the 150-Foot Solar Tower

Disk of the sun with sunspot comparison

Disk of the sun with sunspot comparison

We briefly walked by the 60″ dome, but we did not get to go inside.  Here’s a comparison shot of me next to the “smaller” dome:

60" domeNext we got to check out the 100″ telescope.  This is where it gets really interesting.  This is a telescope that I’ve only seen in photos, and even the photos I’ve taken don’t come close to showing the sheer size and mass of it.  Just up the road a little further from the 60″ dome lies the 100″ telescope across a bridge, a bridge where there is a plaque showing a photo of Albert Einstein standing on the bridge with a few other notable scientists.

Standing in the spot where Einstein was, overlooking the huge dome.

Standing in the spot where Einstein was, overlooking the huge dome.

I’ve taken several photos of the inside of the observatory, but like I said, they don’t do it the justice it deserves.  If your not taking the tour and just walking around, there is an area to the left of the observatory open to a small viewing area with some large windows looking into the observatory.  Before the tour began, we walked around and went into this room, and stared in awe at the telescope through the window.  but being up close and personal with it is a whole different experience.  On our tour, we get to go up a different way to the observing floor.  Through the door pictured above in the background is what is like a large garage, there is even a garage door on the side!  Then starts the stairs. And more stairs.  And more stairs.  Up the first flight is a small area with a phone booth, showing different phones used throughout the time of the observatory.  They just never got rid of anything!

The "phone booth"

The “phone booth”

And now, the moment you’ve all been waiting for, we enter the observing floor of the 100 inch.  Well, the first impressions are, as you might imagine, that it’s big!!  It’s much bigger standing next to it than looking through a window.  I remember reading about the silvering chamber under the floor where the mirror is pulled out for recoating every few months, and clear as day is this big circle where a very large and heavy mirror is lowered.  We got to go upstairs onto the part where the dome rotates, and controls.  Here’s some photos.

This is the view from the floor.  It is too big to fit in the photo.

This is the view from the floor. It is too big to fit in the photo.

The original control board remains, it, and everything else in here is 97 years old.

The original control board remains, it, and everything else in here is 97 years old.

100"3

View from the upstairs on the rotating dome section.

This next photo is pretty cool, because it shows up inside the mirror cell and looking at the primary mirror.  The primary mirror is made of plate glass, and it one solid piece.  It weighs 9000 pounds and is 12″ thick.  In the photo you can see the back side of the mirror (green) and you can see some of the pads that support it.

mirror cell

Well, the last set of photos I have is a fairly recent modification for visual use that seats the eyepiece to a much more comfortable angle.  It appears that there has been a modification to shoot the light gathered from the 100 inch mirror down at the back of the telescope, by means of a huge prism and a refractor tube equipped with a 2″ Crayford focuser.

I found that the tube is from an Explore Scientific refractor, and the focuser is an Astro Physics.

I found that the tube is from an Explore Scientific refractor, and the focuser is an Astro Physics.

Here is a link to a great article on the history of this telescope. Link. That’s about all I’ve got for photos.  After the observatory,  we went out to a special viewing spot called Echo point, with a beautiful view of the entire area, we could easily see the ocean and Catalina Island and even San Clemente Island.  All in all, it was an awesome trip, a lot of walking, and a lot of fun.  I’d highly recommend taking a trip up to Mount Wilson, you won’t be disappointed. I’d love to go back soon and do some observing with their big telescopes!

Observing Report: Prescott with BIG scopes

Well on November 8 we took a trip up to Prescott Arizona to visit my grandparents, and as I have mentioned before on here, my grandpa is an astronomer- at it for 59 years! Anyway, Saw a LOT of stuff but I posted it on Cloudy Nights.  So as not to repeat, here’s the thread.

One thing I don’t think I mentioned the thread, but the seeing (how steady the air is) was rated a 10/10.  I have never seen skies so still before.  One thing about going to dark skies is that I have found that you have to sort of re-learn the stars.  I remember when I got into the hobby I visited dark skies- it was stunning.  So stunning in fact, that I  could not stick to my observing list.  I found myself just looking up rather than through the telescope.  It was like the first trip or two.

Now when I visit the dark skies, I am still awestruck by the skies, but can get to work.  I don’t really make observing lists, rather, I look on star charts at a certain constellation at what’s in the area and for a while, I’ll sweep through the constellation, looking at everything there is to see.  When I have swept a few constellations of their most interesting targets, I go back and choose from the most interesting objects and sketch them.  While in Arizona, I made only three sketches, but that’s ok.  Generally, the sketches take time to do, but it does vary on the object.  I’ve sketched objects in 10 minutes and some objects take as long as an hour to do.  Even on the easier objects where I don’t think there will be much detail, I stick with it and find detail that often gets overlooked.

I’m not sure if I included this in the thread, but the last object I looked at up there was Jupiter.  It was getting pretty high by then (about 3:40 AM).  The seeing was just so good that I was able to put on a very high magnification and the image would hold up.  The highest magnification I went up to was 609x (this is with the 16″).  The image was still good, and could have definitely taken more.  The image was as good as in my 12.5″ reflector.  The Great Red Spot was out, and I could see white swirls in it.  The view that I had was one of the few times that it looks exactly like a photograph or better.  By this time the temperature had dropped to about 37 degrees F* and I went back in.

Hopefully I’ll be able to be making some sketches of Jupiter soon as I have not made one in a very long time, looking forward to it with the 6″ and 12.5″ especially!

Meade Lightbridge 16" F/4.5

Meade Lightbridge 16″ F/4.5

New Project: Criterion RV-6

Hi everyone, well it’s been a LONG time since I’ve posted, but now that school’s out, let the blogging commence! Anyway, I recently acquired a vintage reflector from a really nice guy, a Criterion RV-6 Dynascope.  I read up on these, and they apparently were top of the line back in the day (1950’s to the late 1970’s).  The RV-6 is a 6 inch F-8 Newtonian Reflector on an equatorial mount with a plug in motor drive for star tracking.  Top of the line back in the day, before the company’s demise with the rising popularity in the late 70’s.

So this is my summer project, restoration of this beautiful telescope.  I took it out for first light a few weeks ago, just as is (after of course cleaning the mirror as it was very dirty with all sorts of material I didn’t know what it was).  I got it roughly polar aligned.  The motor drive plugs into a standard outlet, and functions very well for it’s age (at this time, I did not know the precise date of this particular telescope). The view? Phenomenal.  My first target was Saturn, and plainly showed 4 moons, and this was not a very clear night.  Banding on the planet was obvious, as well as detail in Saturn’s rings.  Very pleasing, refractor-like images and sharpness. Collimating well is the key to better views in even cheap telescopes, but when you collimate well with a scope like this, it’s awesome.

My next target was M13, the famous sparkling globular in Hercules.  Now remember, where I live, there is very severe light pollution, and pulling detail out of deep sky objects, even bright ones is a challenge.  But, having good eyes has helped, I’ve pulled M81 and M82 out of my Observer 70mm from here in La Verne, which is quite an accomplishment I’ve heard.  Some people struggle with acquiring this in a 6 inch scope, but a 70mm? Wow.  Where were we? Yes! M13 with the RV-6.  My Orion Expanse 15mm eyepiece yields about 80x in this scope, and the view was spectacular. Very bright, round, on the verge of some resolution even at such a power as low as 80 (which is rather low for observing DSO’s. Averting my vision in various directions will make the glob “grow” and brighten, and make it very grainy.  The most satisfying part of the view was that it wasn’t moving! I’m sure I’ll discover that when seated (this scope’s designed to have the user remain seated) and tracking, I’ll pull out much more detail.  Mating the barlow lens with the 15mm yields about 160x.  Now it was getting interesting.  With direct vision,  the glob took up about 1/6 of the field.  Averted and direct showed numerous faint member coming out of the backround.  When it’s averted, the glob gets huge! So there you have it, my first light of the classic RV-6 Dynascope.

The RV-6 when I first received it

The RV-6 when I first received it

So, before I got into it, I knew I should make a scheduled plan of what to do and how to do it.  I made an immediate decision to refurbish the OTA before the mount, which would simplify things right from the start. First off, the condition the tube is in needed a lot of cosmetic help, meaning paint and hardware.  Some tape had been put on the tube as a marker to show where to put on the tube rings for balance.  Well, they were stuck on there good, I don’t know what kind of tape it was, but I pulled off a good amount of it, and sanded the rest down.  I had already decided to give the scope a brand new paint job, so I used the existing paint as a sort of primer, and sanded it really smooth.  The tube is a kind of cardboard, called bakelite back when it was first invented.  All in good condition, except for a small piece scraped off at the edge of the top of the tube.  For the paint, I did not want a bright glossy white, but rather I chose a glossy (not original) Vintage White color, from Rustoleum.  Took 2 cans to do, and also will be needing a clear-coat as a finish.  So right now with that, I’m making sure the white is completely dry for the last coat.

 

Post paint

I also painted the 6x30mm finderscope in the same color as the tube, and it looks great, but, the side of the tube is engraved with “Criterion”, and it might prove difficult to repaint this back to black.  If things continue going at this pace, expect to see a completely refurbished, put back together, working RV-6 by hopefully the beginning of July.  I think the tube will be finished rather soon as there really isn’t much to do there, just cleaning, and minor paint touch-ups here and there, nothing big, but I think it’ll look awesome when this project is done, and also, a great scope to use!

Fully Polished Mirror, and the Support

After 4 months of work, my telescope primary mirror is finished.  I started this project on the 18th of August and finished on December 31st, with a few hours to spare before the new year.  I thought that would be a goal, because I’m going to submit my work (a report basically) to win the National Young Astronomer Award, from the Astronomical League.

The winners (first, second, and third prize)  get an all expense paid trip to the ALCON (Astronomical League Convention) and of course the prize.  First place wins a five inch refractor telescope- a pretty good prize, see the details of this scope here.

Anyway, the telescope mirror is finished and that’s a huge part of the telescope.  For the reflective optical coating I chose Destiny.  My mirror will run a mere 30 dollars- after checking other companys, they averaged about 50 dollars for a mirror of this size.  I also bought a secondary mirror and spider for a small sum.  1/10th wave optics, 1 inch size, 15 bucks is pretty hard to beat.

Upon finishing my mirror, I counted up all the time working on my mirror, from start to finish.  Total time of the glass in motion was over 25 hours!  It may seem like not that long, but it feels longer because of the precision I had to maintain during the process.  Total polishing time clocked in at 6.7 hours- a little longer than expected.  But it’s rouge, one of the slowest polishing compounds you can buy.  And it was worth it considering that it is said to give a finer polish than Cerium Oxide, which is also three times the polish.  Oxide polishes faster, but the increased price was not worth it to me.

Finished Mirror

For me, one of the most important parts of the telescope making project is putting your initials and the date you finished it on the back of the mirror.  It was just as exciting as I thought it would be.  It may seem insignificant, but I liked doing it.

IMG_3203

Also completed was the mirror support, or cell.  It consists of two circular pieces of wood, one the size of the mirror and one the size of the telescope tube.  The mirror sits on the upper piece, and is secured with “L” shaped clamps.  In between the pieces are 3 long screws, and attached are 3 springs.  Next comes the wooden piece for the tube.  Under that, the the ends of the screws are exposed, and wing-nuts are then threaded on.  By twisting on of the wing-nuts, it compresses the spring and moves the mirror on top slightly downward on that side of the mount.

IMG_3210 IMG_3209

mirror in the support

Pretty good huh? I bought an aluminum tube at the hardware store for 7 dollars.  It is five inches round, so the bottom piece of the support matches that.  Obviously, the “L” clips will need to be painted black and other stuff to eliminate reflections.  There’s not that much left to do on the scope really.  I had the bottom base for the Dobsonian mount finished- with a CD as the bearing material, which works really good by the way.

I'm building a mount similar to this.

I’m building a mount similar to this.

Well to wrap things up, I finished a big important part of my telescope and I’m glad I took my time with it.  Pretty soon I’ll be gazing upon galaxies and nebulae.  I think the biggest help will be the aperture.  If you’ve heard great things from Orion’s Skyscanner, my scope has the same aperture.  It also has a much longer focal length (f-12) and should, if collimated correctly, provide sharper images.

Telescope Polishing- Update

Almost polished mirror

Almost polished mirror

As you can see, the mirror is polishing pretty good but it is taking a long time to do, they weren’t lying when they said rouge is really slow, not to mention incredibly messy.  The large grey mass is on the back of the mirror- I got careless during the 3rd grade of abrasive and accidently set the mirror down face up. See post (here). All of the scratches you see are on the backside of the mirror.  Also, after repeated “cold pressing” sessions, the mirror refuses to polish from the center to the edge.  I have heard of this before, and it usually causes a turned edge.

polished

As you can see above, the area in the middle is not polished yet.  This is often hard to distinguish from the ground surface on the back, but at the right angle, I can see it.  I was lucky enough to capture it in the picture.

Unfortunately, the lap in the previous post was ruined by dropping it, I am reckless sometimes.  Then I made a new lap, and let it sit too long after pouring it and it hardened before I could put in the curve.  The next lap polished a lot and then, for some reason, the lap started to crack around the edges.  It eventually came off so now I have to make another lap.  The books don’t lie, polishing with rouge and pitch are not easy.

Rouge

Up close with Rouge and the polishing process.

Polishing operation, as always covered with Rouge

Polishing operation, as always covered with Rouge

Making the Pitch Lap, and Polishing

I’m waist deep in the polishing process of the telescope making project, for me this is the final stage.  As I stated at the beginning of this project, I would omit the Foucault test as well as figuring of the telescope glass.

In truth, I had to make 2 pitch laps.  The first one was okay, but now very good.  The “channels” that were cut were far too shallow, and the lap came out lopsided.  Besides, I got a little anxious to finish this mirror and polished before fine grinding was done.  So I had to scrape off the lap with a knife and return to fine grinding.  How did I know? Well, the surface was more frosted than it should have been for starters.  Also, I found that there was a scratch that went unnoticed.

So another hour and a half of grinding is what it took to correct these few problems.  The new pitch lap is much better and it’s polishing!  Below is the setup of the area for the pitch lap making:

Lap making setup

Now, before I get into the whole process, because it is an involved one, let me state that this only one way of making a pitch lap.  There are probably hundreds of ways (no I’m not kidding) to make a successful pitch/wax lap.

All of the books I read on this stage were advising the beginner not to make a lap of pitch, but I didn’t listen, because of extensive research and tips of the actual process.  You may wonder why I said “wax” in the preceding paragraph.  That’s because a lot of people have made wax laps over the years, mainly of beeswax.  I’m not sure if you can purchase beeswax sheets anymore, but maybe some are still around.  The beeswax lap serves as an economic alternative to the traditional pitch and is easier to make (not anymore unfortunately).

On to my lap making process!

The first thing to do is to open up the pitch package, put it in an old pan, and heat it very slowly.  Because I am trying to be as economic as possible, I decided to purchase a synthetic lap, Acculap Pitch.  I bought the intermediate grade as it is best for laps of this sort, which can be purchased here.

While the pitch is heating, the surrounding area should be covered well in newspaper (see above photo).  Also, I got a large bowl and put hot water in it, then the two glass disks.  This is probabilistic one of the tensest parts of making the lap, for if even a single drop of cool water gets on a glass disk, it will crack it and it’s over.  Luckily, that did not happen.

Be sure to watch the pitch lap closely, and I meant it when I said to heat it slowly, because I became a little impatient and heated it too fast, and it started to bubble, which hardens the pitch.  Fortunately, the addition of turpentine can bring it back to it’s normal hardness.  But be careful if you do this to not get any in the flame, because of the explosive properties of turpentine.

The reddish hue is due to the Rouge from the previous lap.

The reddish hue is due to the Rouge from the previous lap.

While all of this is going on, I took a small bowl of water and filled it with warm water and a soap solution of dishwashing detergent, this will be lubricant to keep the mirror and lap from sticking while pressing is in progress.  Also, when the pitch is poured, a cardboard damn will need to be made to retain the pitch on top of the tool.  This was made out of a cereal box, and the glossy, printed side was facing in as its able to retain the moisture of the pitch.

When all of this is finished, the pitch should be very liquidy, though still thick as pitch is.  Then I removed the tool from the water bath, dried it very thoroughly to promote good adhesion of pitch and slowly poured the pitch onto the tool.  I decided to have this lap much thinner than the previous lap, because if I have to scrape it off again, it will be much easier to accomplish.

Freshly poured pitch

Freshly poured pitch

Now I let it sit for 5 or six minutes, for the pitch to harden enough to peel off the cardboard dam.  This is my favorite part.  There’s just something about the lap that really looks sharp, or as sharp as a slab of pitch on glass can look.  I did not get a photograph of it, but it still remains in my mind.  Now one of the most critical parts- pressing.

Now the soapy water comes into play.  I poured a liberal amount of the stuff onto the warm lap, then slowly set down the mirror.  Now I move the mirror slowly around a half an inch to 1 inch in different directions, also rotating the mirror.  I thought I made good contact and it feels smooth when I polish, but the edge is polishing before the center, which means the dreaded turned edge.  This can be fixed, but I need to cold press, which is a process where a rouge lubricant is put between the mirror and lap and a weight is put on top of the tool to sit for 30 minutes or more.  The only problem is that the lap dries rather quickly and I don’t want to get them stuck together.

Getting back to the lap making, I slid the mirror off after I though good contact was made, and let it cool off for a couple of minutes, and then proceeded to cut the channels.  In Amateur Telescope Making, they recommend using a razor blade to cut these large channels.  They even have pictures of  someone cutting a perfect, flawless lap from a razor blade.  This is however, not the case.  What follows is jagged, uneven impressions, and almost every time chipping off large pieces out of the face of the lap.  Me and my Dad learned this making the previous lap, which by the way, my Dad is a huge aid to me during this process.

So just to see, we tried a couple of lines, and it came just as described.  So my Dad came up with a genius way to make good channels, a small handheld grinder.  This served perfect for making neat, and good looking channels.  What was most amazing to me during cutting these channels is the effect of the ground up pitch.  I grinds it into this very fine fuzz, the closest thing being cotton candy.

A finished pitch lap

A finished pitch lap

It is not the best lap I’ve ever seen, but it does it’s job like it should.  For polishing, I decided to use Red Optical Rouge.  I would prefer to use the faster polishing Cerium Oxide, but it’s more than triple the price for the stuff and like I said, this is a budget project.  I have heard that Rouge gives a better polish that Cerium Oxide though.

The main difference between grinding and polishing is that in polishing, you have to be very careful when you have the lap on the stand.  It should be dust free, and the work is so delicate that dust will scratch the polished surface.  You wouldn’t think there would be any chance to get dust between the disks, but there are actually many.  For example, you expose the lap when you go to renew the charge of rouge.  So to stop this, I put a piece of plastic or a sheet of paper over the exposed lap to keep dust to a minimum.

One thing about using Rouge is that is is abominably messy.  The stuff gets everywhere! And it’s all over your hands most of the time, so when you go to wash your hands with a bar of soap, the bar will be covered with rouge.  It gets on clothes, doors, doorknobs, towels, even in your hair!

My new goal is to be finished with the entire project by the end of the year, which is not a whole lot of time.  I probably won’t get the mirror aluminized, but everything else (I’m hoping) will be finished.

Focal Length Test

As I progress through building my telescope, it is important to know and understand the focal length, or distance where all of the light from the star forms into an actual image at one point.  There is a simple yet effective way to do this.  You don’t need much, but a checklist is helpful.

When I perform this test, I use:

a bucket  halfway full with clean water

a tape measure that extends to about 100 inches

the mirror (duh)

a piece of chalk or card to mark the distance

and a white poster board (optional but it helps)

Here is the setup:

So here’s the steps from Building a Reflecting Telescope:

 

As you can see, the process is so simple and straight to the point that I will agree not to explain what is being depicted.  My results came out well as expected.  I was aiming for an f/12 telescope, which would yield a 48 inch focal length, and it came in at 47 inches.  No harm done, as an inch will not effect the performance in the least bit.

As I was grinding on the weekend, I am on the last 2 abrasives; aluminum oxide 9 and 5 micron.  It is said that when grinding has been successfully completed, the mirror will feel like the finest satin to the touch, and newsprint can be read through it.  It’s already unbelievably smooth, and not quite able to read through, but nevermind.

I caught a snag while finishing my abrasive: I scratched the mirror’s surface near the edge.  I’m not quite sure how it happened, but my best guess is that somehow, dirt of some sort got between the glasses, and scratched.  If this furrow was near the center, I wouldn’t be stressing over it as much.  It takes about 3 times as long to remove such a thing at the edge than one near the center, as the glass naturally grinds out fastest at the center.  Oh well.  I knew that I would get a scratch at some point, but I’m happy it wasn’t during polishing, or I would have been in some serious trouble.

Hope to be finishing this project soon, because I’m itchy to look through this telescope!

 

Project Update: Telescope Making 4

The continuation of my telescope making project is making headway.  I just got all of the abrasives necessary to finish all for the grinding .     I ‘m making good progress, but the going is slow.  I used my grandpa’s book that he made in the 1960’s-  Building a Reflecting Telescope.  Don’t try to look for this book, because it was never published.  It does have some very good drawings and explains a simplified way to build a telescope.

Well, I’m doing an even more simplified version of his book.  I found in the last chapter of Amateur Telescope Making.  Here’s a quote:

“For the first mirror we had to abandon Pyrex, the mirror handle, the pitch polishing lap, and the paraboloid.  We teach the beginner some of the rudiments of the Foucault test but only because we are present to coach the worker in its use.  Although pitch laps give finer polish and fewer zones, they are so difficult for the average beginner to make and alter that we regard them as the principal bottleneck in mirror-making.  They have discouraged more beginners than any one thing, or any ten things.  Although we get fewer fine mirrors with honeycomb foundation, it best suits our purpose, which is to finish the first mirror while the maker’s enthusiasm lasts.”

I pretty much agree with everything that they are stating here, and this “group” is the telescope making group from the Cleveland Museum of Natural History.  I checked out their website, and I’m pretty sure that they don’t make telescopes there anymore.  Apparently, there used to be a free program to build your own telescope from scratch, using a honeycomb foundation instead of regular pitch.  The only thing I don’t agree with is the part for a beginner not being able to make a successful pitch lap.

I guess that that this does not apply in my case as I have telescope making in my blood (thanks grandpa).    I’ve set up a grinding schedule and I plan to follow it quite closely.  I plan to grind through one grade every weekend.  I have 5 more grades to grind through, so I guess I won’t finish it by my birthday, but I’m not devastated.  Good mirrors take time, and that’s fine by me.

On Friday, I was really excited so i made some good progress through Saturday as well.  I ground my way through Silicon Carbide #320 and then on to White Aluminum Oxide 25micron.  It is very strange going from this muddy grey sludge to a white sludge.  The abrasive is becoming so fine that it doesn’t really feel gritty.  The only similar substance I can use to describe it is powdered sugar.

I have also thought about starting a new WordPress blog.  I want to do a blog that is like a sketch reference website.  But it has to be with at least 1 small telescope, as well as with a bigger telescope.  Of course, I have to have a lot of objects sketched in order to that, and I haven’t done that.  I have made many sketches, but not 110, yet.

Also, they would probably need to be black paper/background to really get noticed.  I have heard of running the white paper sketch through a scanner and then altering it to a negative image, but I don’t have a scanner, so I guess that means I have to use real black paper.  But that’s fine with me, I’ve been eager to use a different media for sketching.  Hopefully, sometime in the near future I can have a sketch on Astronomy Sketch of the Day.

Someday, I will make larger, more complicated telescopes as well.

Astronomical Sketches: Old And New

I’ve been going through some of my old observing notes lately and pulled out my very first astronomical sketch book.  I took a few minutes and looked through every page.  If you’ve seen my recent sketches, they are perfect representations of what you would see through the eyepiece, except they are negatives.  All of the sketches in my first book were all made with #2 pencil.

My first sketches were made on lined paper and the sketching circle representing the field of view in a telescope eyepiece was just merely hand drawn.  These first sketches were crude, and they were not descriptive or an accurate sketch either.  I the went to taping circular pieces of sketching paper which proved much better.

I was still not very satisfied with my results, and wanted more oomph from the sketches.  I read Steve Coe’s Deep Sky Observing, which is one of the best deep sky/ sketching books I have ever read.  Then came the perfect set up.  I has ample room for notes, including dates; times; and telescopes used plus a 3 inch circle complete with North and East markings.  These could be made on the computer and were used with ease.For an example of what these sketches look like versus the real thing: I have a picture of the real object and one of the sketch I made.

 

 

 

 

 

 

 

 

 

 

This object is a planetary nebula- the Dumbbell Nebula (M27).  See the Dumbbell? The sketch was made using my small 70mm Refractor, and the view would have been much more impressive from a darker sky.  For those who live in light polluted skies, you feel my pain and know what I am talking about.  There is one other type of deep sky object I like to sketch: globular clusters.  At first I thought this was not possible but once again, referring back to Deep Sky Observing, it shows how to sketch these stellar nodules of stars in space.

The view through a small telescope is dramatically less impressive than looking at a high quality photograph.  A strip of 35mm film can capture much more light than your eye.

 

 

 

 

 

 

 

 

 

 

You can really see the difference in globular clusters obviously.  By the way, Hi Digi Com and Media!

Building your own Telescope

Hi everybody, and today is all about making your own reflecting telescope.  I’m sure that a lot of you have heard of this before but never have actually attempted it.  I have found a website where plate glass mirror blanks are very inexpensive.  I am about to start to make my own 4 inch f-12 reflecting telescope.  If anybody is interested in maybe starting a telescope making club, you are more than welcome to share your ideas with me on the comments or you can email me at observer70nrs@gmail.com .   I will try to reply to you as soon as possible, which will probabily be no more than a day’s wait because I am on summer vacation and have a lot of time on my hands.

The website is   Telescopemirrorblanks.com

 

 

Another good website is one that tells you about a really good mounting if you are interested.

It is        http://blog.modernmechanix.com/the-poor-mans-telescope/

Happy  grinding!